Jump to content

BR Standard Class 8

This is a good article. Click here for more information.
From Wikipedia, the free encyclopedia

BR Standard Class 8[1]
The sole Standard Class 8 locomotive crossing the Somerset Levels, 2010
Type and origin
Power typeSteam
DesignerRobert Riddles
BuilderBR Crewe Works
Build dateApril 1954
Total produced1
Specifications
Configuration:
​
 • Whyte4-6-2
 • UIC2′C1′h3
Gauge4 ft 8+1⁄2 in (1,435 mm) standard gauge
Leading dia.3 ft 0 in (0.914 m)
Driver dia.6 ft 2 in (1.880 m)
Trailing dia.3 ft 3+1⁄2 in (1.003 m)
Length67 ft 8 in (20.62 m)
Width9 ft 0 in (2.74 m)
Height13 ft 0+1⁄2 in (3.98 m)
Axle load22 long tons (25 short tons; 22 t)
Adhesive weight66 long tons (74 short tons; 67 t)
Loco weight101.25 long tons (113.40 short tons; 102.87 t)
Tender weightBR1E: 55.5 long tons (62.2 short tons; 56.4 t)
BR1J: 53.7 long tons (60.1 short tons; 54.6 t)
Tender type1954–1958: BR1E
1958–1962: BR1J
Fuel typeCoal
Fuel capacity10 long tons (11 short tons; 10 t)
Water cap.BR1E: 4,725 imp gal (21,480 L; 5,674 US gal)
BR1J: 4,325 imp gal (19,660 L; 5,194 US gal)
Firebox:​
 • Grate area48.6 sq ft (4.52 m2)
BoilerBR13
Boiler pressure250 psi (1.72 MPa)
Heating surface:​
 • Firebox226 sq ft (21.0 m2)
 • Tubes and flues2,264 sq ft (210.3 m2)
Superheater:
​
 • Heating area677 sq ft (62.9 m2)
CylindersThree
Cylinder size18 in × 28 in (457 mm × 711 mm)
Valve gearCaprotti valve gear
Valve typePoppet valves
Performance figures
Tractive effort39,080 lbf (173.84 kN)
Factor of adh.3.78
Career
OperatorsBritish Railways
Power class8P
Numbers71000
LocaleLondon Midland Region
WithdrawnDecember 1962
DispositionPreserved, undergoing overhaul to mainline standards
Hear 71000 at work
71000 passing St Andrew's Junction
(A steam locomotive makes a lot of noise when working hard: play loud for realism)
Problems playing this file? See media help.

The BR Standard Class 8 was a class of a single 4-6-2 Pacific steam locomotive designed by Robert Riddles for use by British Railways. Only the prototype was constructed, which was christened Duke of Gloucester. Constructed at Crewe Works in 1954, the Duke, as it is popularly known, was a replacement for the destroyed LMS Princess Royal Class locomotive number 46202 Princess Anne, which was involved in the Harrow and Wealdstone rail crash of 1952.[2]

The Duke was based on the BR Standard Class 7 Britannia design. It incorporated three sets of modified Caprotti valve gear, relatively new to British locomotive engineering and more efficient than Walschaerts or Stephenson valve gear. The Duke was regarded as a failure by locomotive crews due to its poor steaming characteristics and its heavy fuel consumption. Trials undertaken by British Railways also proved disappointing, revealing problems with the draughting of the locomotive, which caused difficulties in adhering to the timetables.

Consequently, the unique locomotive had an operational life of only eight years. It was taken to Woodham Brothers scrap yard in Barry, Vale of Glamorgan, South Wales, but was saved from being cut up when it was purchased by a group of railway enthusiasts, who restored it to as-built condition over 13 years. Since then, modifications have been made to the original design, creating one of the most efficient and powerful steam locomotives ever to run in Britain.[3] As a result, the Duke of Gloucester has been frequently seen on the mainline around Britain. As of 2024, the locomotive was being overhauled to return it to operational condition.

Background

[edit]

Riddles had frequently argued the case for the inclusion of a Standard Class 8 Pacific in the standard range of locomotives being introduced by British Railways. However, those proposals were rejected by the Railway Executive on the grounds that attempting to develop a new form of steam motive power was unnecessary because there were enough Standard Class 7 Britannia locomotives already available for use.

However, opportunity came out of adversity when the short-lived rebuild of the former LMS Turbomotive, 46202 Princess Anne, was destroyed in the Harrow and Wealdstone rail disaster of 1952.[2]: 64  A gap then existed in the roster for locomotives with 8P power classification, for which there was high demand to allow the efficient operation of heavy expresses on the West Coast Main Line between London Euston and Scotland.[4]: 460  That gave Riddles the perfect opportunity to press the case for his new design, a prototype of which was duly authorised for construction.[4]: 490 

Design details

[edit]
71000 Duke of Gloucester on the East Lancashire Railway, 2009. Note the British Caprotti valve gear.

At first, Riddles wanted to develop an enlarged version of his Standard Class 7 Britannias, because that design still featured a two-cylinder layout.[1]: 188–189  However, the size of the cylinders needed to achieve the 8P power classification would mean that the locomotive was outside the British loading gauge, so a reluctant reversion to the three-cylinder layout ensued.[2] That reluctance was born from experience with the Gresley Pacifics, in which the conjugated valve gear was difficult to maintain, due to the middle cylinder being located between the frames.[1] Therefore, an alternative type of valve gear had to be found.

A rotary cam-driven form of Caprotti valve gear was settled on, as developed by Heenan & Froude, using poppet valves.[5] It was based on Italian locomotive practice and allowed precise control of steam admission to the cylinders, as well as improving exhaust flow and boiler draughting when compared to the more conventional Walschaerts and Stephenson valve gear.[5] On paper, that created a free-steaming, hard-working locomotive, capable of hauling heavy loads over long distances but, in practice, fundamental design errors, and undetected deviations from the drawings made during construction, combined to prevent the locomotive from achieving its expected performance during British Railways ownership.[6]

The main problem was known even when the locomotive was under construction, because L.T. Daniels, the representative of the British Caprotti company, recommended the use of the Kylchap blastpipe, which could have coped with the fierce exhaust blasts experienced with the Caprotti system.[1] A standard double chimney of the Swindon type had already been fabricated in order to cut costs and it had been installed in the smokebox, supposedly before Riddles could do anything about it.[1] As a result, the locomotive suffered due to the choke area of both the chimney and blastpipe being much too small for the pressure created by the exhaust, which led to poor draughting.[7]: 29 

Further problems relating to the firebox of the locomotive were only discovered during its restoration, including a poorly dimensioned ashpan, and dampers that were too small, starving the fire of air when operating at speed.[7]: 58  Further, concurrent with the construction of 71000, British Railways "Modernisation Plan" was under development, raising questions about the need for the locomotive.

Following the occasional appearance of cracks near the spring brackets of the Britannias and Clans, a substantial rearrangement took place in that area, which resulted in the locomotive riding on three cast steel "sub-frames" carrying the ten front-most spring brackets, and lengthened spring brackets behind the rear driven axle. Perhaps remarkably, they were not integrated into a cast combined sub-frame/pony truck pivot stretcher, the pony truck pivot stretcher being a fabrication. Had the planned batch of smaller Pacifics been built, they would have been fitted with that arrangement.[8]

Construction history

[edit]

The opportunity to create an entire batch of locomotives within the 8P category was declined by the Railway Executive. It had been said[by whom?] that was because the design process had been very expensive and complex, so that when the locomotive emerged from Crewe Works in 1954, the construction of similar locomotives was seen as inappropriate, especially given the 1955 Modernisation Plan.[7]: 58  As a result, 71000 remained the solitary member of the proposed class of Standard 8P locomotives.

Naming the locomotive

[edit]

After emerging from Crewe Works in 1954, the locomotive was named Duke of Gloucester prior to entering revenue-earning service. Had further locomotives been constructed, they would have belonged to the Duke Class, standing alongside the sister locomotives of the Britannia and Clan Classes. Since then, the locomotive has colloquially been referred to by steam enthusiasts and crews as the Duke.

Operational details

[edit]

The Duke was highly unpopular with crews, who regarded it as something of a liability due to its poor steam production.[1] Inefficiencies caused by the problems regarding its draughting abilities and firebox design meant that no further examples were constructed.[9] The fact that no effort was made to rectify the problems indicates the change in policy regarding steam locomotives, with the Modernisation Plan coming into operation just as the "Duke" entered service.[1] Based for its entire working life at Crewe North depot, the locomotive was used to haul boat trains on the undemanding North Wales Coast Line between Crewe and Holyhead.[1] All those factors culminated in the locomotive having a short service life of only eight years, being withdrawn from service in 1962.[2] The reputation of the locomotive amongst its crews as being a poor steamer was eventually to disappear, but only after it was rebuilt following its rescue from the scrap yard in 1974.

Livery and numbering

[edit]
71000 at the terminus of the West Somerset Railway at Minehead, 2010

The livery of the "Duke" was a continuation of the British Railways standard class practice. The class was given the power classification 8P.[10]: 82–83  Following on from the 'Britannias', the "Duke" was numbered under the British Railways standard numbering system in the 71xxx series.[10]: 82  The "Duke" was given the number 71000, and featured brass nameplates with a black background, located on the smoke deflectors.[10]: 84 

Preservation

[edit]
No 71000 Duke of Gloucester on the East Lancashire Railway, 2007

After withdrawal, the "Duke" was selected for inclusion in the National Railway Museum, but it was later decided that only the cylinder arrangement was of interest.[2] One of the outside cylinders was removed for display at the Science Museum, and the other was removed to restore balance in readiness for scrapping. The locomotive was purchased by Dai Woodham, though it was initially sent to the wrong scrapyard. After being retrieved, the "Duke" languished for many years in Woodham Brothers scrapyard, before enthusiasts purchased the locomotive in 1974, forming the Duke of Gloucester Steam Locomotive Trust.[2]: 65 

Restoration began in earnest, though with many components missing, the most expensive of which being the Caprotti valve gear, it took 13 years of effort on the part of enthusiasts, with assistance in the guise of sponsorships from industry, to return the locomotive to near as-built condition. One of the very few compromises made was replacing the previous steel cylinders with spheroidal graphite iron.[2]: 65 

Two significant construction errors were discovered during restoration:

  • The chimney was too small compared with other locomotives of similar size, resulting in poor boiler draughting at times of high steam demand.[11]
  • The firebed (grate) air inlet dampers had not been built to the drawings and were too small, resulting in poor air supply and inefficient combustion.[11]

Those errors were corrected and the opportunity was taken to incorporate some other improvements, including the previously recommended Kylchap exhaust system, which finally unlocked the locomotive's true potential as a powerful express passenger locomotive.[1] When the "Duke" was first allowed to haul a full load on the main line, it became immediately obvious that the boiler was producing steam at a more efficient rate and that the reborn "Duke" was unrecognisable from the failure experienced under British Railways ownership.[3] With the modifications, the "Duke" is now one of the most powerful steam locomotives ever to run on Britain's railways, past or present (the LMS Coronation Class Pacifics held that title under British Railways auspices - the three cylinder "Duke" never actually achieved the 3000 cylinder horse power figure that was recorded by the four cylinder Princess Coronation Class). Ironically, it is not only more powerful than the English Electric Type 4 diesel locomotives which replaced it directly in service, but also the type 4 and 5 diesel locomotives built to replace the earlier diesels.[1]

In the 1995 "Shap trials" (30 September to 3 October) 71000 broke the record for the fastest northbound ascent and achieved the highest Estimated Drawbar Horsepower (EDHP) figures during the event, its average over the Shap ascent was 2300 EDHP and peak 2803. The Duchess of Hamilton (46229) generated EDHP figures of 2150 and 2343 respectively. The A4 Sir Nigel Gresley (60007) suffered from poor coal and possible leaking tubes so only achieved an EDHP of of 1671 (average) and 1812 (peak).[12]

In preservation, the "Duke" had an impeccably reliable operational record. However, on 9 June 2007, the engine operated a railtour from Preston to Carlisle returning via Settle, where, for operational reasons, the locomotive's start position was changed to Carnforth.[13] A little over 30 miles (48 km) into the journey, the locomotive was stopped at Penrith with leaking tubes in the firebox and removed from the train.[13] It was withdrawn for repairs and returned to service in January 2008.[13]

Because the locomotive now bears little mechanical resemblance to that which operated under British Railways, it has also been used as a test bed, incorporating several other modifications and innovations.[2] They are intended to investigate how much further the locomotive's performance can be enhanced, raising speculation about the capabilities of an entire batch of Standard class 8 "Pacifics" had history been different.[1] In 2012, the locomotive was withdrawn from service because its boiler ticket expired. After many setbacks, the boiler was fired up and tested in late 2023.[14] As of 2024, the locomotive is in the final stages of its overhaul and was expected to be operational sometime later that year.[15]

Models

[edit]

A ready-to-run model in O scale, produced by Ace Trains, was released in Summer 2019,[16] built to coarse scale standards, which apply mainly to the wheels rather than the model more generally. Uniquely, the model has a representation of working Caprotti valve gear[citation needed]

The only well-documented construction of working live-steam scale model of Duke of Gloucester in Model Engineer magazine was by Denis Evans,[17] of Blackpool, England. Beginning in the 1966, and using original drawings from British Railways and Associated Locomotive Equipment (a subsidiary of Heenan & Froude), Evans built three Dukes, with fully working Caprotti valve gear, first in 7¼ inch gauge,[18][19][20][21][22][23][24][25] and then 5 inch[26][27][28] and 3½ inch[29][30][31][32] gauges. The 7¼ inch gauge Duke won awards at the 48th Model Engineer Exhibition in 1979,[33] as did his 3½ inch gauge locomotive at the 61st Model Engineer Exhibition in 1992.[34]

References

[edit]

Citations

[edit]
  1. ^ a b c d e f g h i j k Herring, Peter. "Standard Class 8". Classic British Steam Locomotives.
  2. ^ a b c d e f g h Langston, Keith. Made in Crewe: 150 Years of Engineering Excellence. Mortons Media. ISBN 0-9552868-0-8.
  3. ^ a b "The changes of the locomotive's characteristics". The Duke of Gloucester Locomotive Trust. Retrieved 30 August 2007.
  4. ^ a b "British Railways prototype class 8 express passenger locomotive". Railway Magazine.
  5. ^ a b "B.R. class 8 4-6-2 locomotive No. 71000". Locomotive, Railway Carriage & Wagon Review. p. 88.
  6. ^ "British Railways standard class "8" locomotives". Engineer. 1954. pp. 8, 19.
  7. ^ a b c HMSO, British Transport Commission (1957). British Railways standard 3 cylinder 4-6-2 express passenger steam locomotive No. 71000 (Report). Performance and efficiency tests. London.
  8. ^ British Rail. "SL/DE/21642, SL/DE/21631, SL/DE/22042" (Drawing). National Railway Museum.
  9. ^ Nock, O.S. (1957). "Performance and efficiency tests on B.R. class 8 locomotive". Engineer. No. 204. pp. 293–294.
  10. ^ a b c Clarke, David. Riddles Class 6/7 Standard Pacifics.
  11. ^ a b "Problems discovered with original features". The Duke of Gloucester Locomotive Trust. 2007. Retrieved 30 August 2007.
  12. ^ Semmens, Peter W. B. (December 1995). Pigott, Nick (ed.). "Shap Performance Trials: The Full Analysis". Practice & Performance. Railway Magazine. Vol. 141, no. 1136. pp. 19–22.
  13. ^ a b c Hopkins, Danny; Streeter, Tony (2007). "The Duke's Bad Day". Steam Railway Magazine. No. 338. p. 89.
  14. ^ "250PSI !!! Listen as steam escapes The Duke's safety valves this week in the presence of the boiler inspector. A great end to the year for our members..." BR Standard Class 8 Steam Locomotive Trust. Retrieved 28 February 2024.
  15. ^ "71000 Trust signs agreement with Crewe". Steam Railway. No. 555. 29 February 2024. p. 15.
  16. ^ "E/31 Duke of Gloucester". www.acetrainslondon.com. Archived from the original on 21 October 2019. Retrieved 2 September 2019.
  17. ^ "Denis Evans". Model Engineer. 202 (4343): 106. 16 January 2009.
  18. ^ D.L. Evans (1 September 1967). "1 1/2 in scale "Duke of Gloucester"". Model Engineer. Vol. 133, no. 3328. p. 840.
  19. ^ "Locomotive with Caprotti valves". Model Engineer. Vol. 137, no. 3428. 5 November 1971. p. 1047.
  20. ^ Evans, Martin (6 October 1972). "Torquay Manor. 5 in. gauge Great Western 4-6-0". Model Engineer. Vol. 138, no. 3450. p. 965.
  21. ^ Evans, Martin (16 February 1979). "48th Model Engineer Exhibition. 'First Impressions'". Model Engineer. Vol. 145, no. 3603. p. 214.
  22. ^ Bray, Stan (19 December 1980). "Midlands Federation Exhibition". Model Engineer. Vol. 146, no. 3647. p. 1518.
  23. ^ Bray, Stan (20 May 1988). "The 7 1/4 in. Gauge Society A.G.M.". Model Engineer. Vol. 160, no. 3825. p. 601.
  24. ^ Chrisp, Mike (6 November 1998). "SMEE 100 The Centenary Exhibition". Model Engineer. 181 (4080): 564.
  25. ^ Arrowsmith, John (4 February 2005). "The 7 1/4" Gauge Society AGM & Rally 2004". Model Engineer. Vol. 194, no. 4240. p. 162.
  26. ^ Evans, Martin (20 October 1989). "Caprotti valve gear on 5" gauge 'Duke of Gloucester' by Dennis Evans". Model Engineer. Vol. 163, no. 3859. p. 508.
  27. ^ Bray, Stan (18 September 1992). "The 62nd Model Engineer Exhibition". Model Engineer. Vol. 169, no. 3929. p. 347.
  28. ^ Wainwright, David (19 February 1993). "Southern Federation Autumn Rally 1992". Model Engineer. Vol. 170, no. 3939. p. 202.
  29. ^ Evans, Martin (5 March 1993). "62nd International Model Engineer and Modelling Exhibition. Duke of Edinburgh Challenge Trophy". Model Engineer. Vol. 170, no. 3940. p. 267.
  30. ^ "The 65th Model Engineer Exhibition at the International Model Show. Loan Section". Model Engineer. Vol. 176, no. 4014. 5 April 1996. p. 385.
  31. ^ Garner, Tom (11 September 1998). "Hindsight (Locomotive building)". Model Engineer. Vol. 181, no. 4076. p. 328.
  32. ^ Bibby, Alan (11 June 2004). "The Northern Association of Model Engineers Exhibition 2004". Model Engineer. Vol. 192, no. 4223. p. 673.
  33. ^ Dupen, P.J. (18 May 1979). "48th Model Engineer Exhibition 1979. The Locomotives". Model Engineer. Vol. 145, no. 3609. p. 563.
  34. ^ Evans, Martin (6 March 1992). "Model Engineer and Modelling Exhibition. Class Reports. The Locomotives. Class B2 (Locomotives under 1 in. scale)". Model Engineer. Vol. 168, no. 3916. p. 278.

Further reading

[edit]
  • Bradley, Rodger P. (1984). The Standard Steam Locomotives of British Railways. David & Charles. ISBN 0715383841.
  • Gilbert, Dr. P. T. (Ed.): A Detailed History Of BR Standard Steam Locomotives. Volume 1. Background to Standardisation and Pacific Classes (Railway Correspondence & Travel Society (RCTS): 1994) ISBN 0-901115-81-9
[edit]
Wikimedia Commons has media related to
BR Standard Class 8.

Retrieved from "https://en.wikipedia.org/w/index.php?title=BR_Standard_Class_8&oldid=1270762805"